LA-34 Series

  • Rigid one piece headstock casting design
  • Electromagnetic brake
  • 18-step speeds for higher torque
  • Auto-lubrication system
  • Cross slide on ballscrews
  • Laser inspected bed
  • Single piece Meehanite bed casting
  • Shafts and gears are hardened and ground to HRC 45±2
  • Optional double chucks for longer workpieces

Request for Info



Specifications

Specification HW-30 SeriesLA-34 SeriesLA-38 Series
Swing Over Bed 30" 34" 38"
Swing Over Cross Slide 21.3" 24.4" 28.3"
Swing Over Gap 38.9" 46" 50"
Width of Bed 15.75" 20" 20"
Distance Between Centers 80" (Opt. 120" / 160") 60" (Opt. 80", 120", 160", 200") 60" (Opt. 80", 120", 160", 200")
Cross Slide Travel 14.75" 11.02" 11.02"
Top Slide Travel 8" 12"
Spindle Bore 4.5" 6" (Opt. 9") 9" (Opt. 12")
Spindle Nose D1-11 A2-11 (Opt. A2-15) A2-15 (Opt. A2-20)
Spindle Speeds 12 18 18
Spindle Speed Range 10-1000 RPM 5 – 670 RPM (Opt. 4 – 500 RPM) 4 – 500 RPM (Opt. 4 – 440 RPM)
Through Hole Diameter 4.5" 6"
Spindle Bore Taper MT#7 MT#5 (Opt. MT#6) MT#6
Thread – Standard (Whit-worth) 44 (2-56) TPI 30 – 0.25 TPI 30 – 0.25 TPI
Thread – Metric Pitch 39 (0.5-14) mm 1 – 120 mm 1 – 120 mm
Longitudinal Feed 0.002"–0.032" in/rev 0.0032 – 0.096 ipr 0.0032 – 0.096 ipr
Cross Feed 0.001"–0.0094" 0.0016 – 0.048 ipr 0.0016 – 0.048 ipr
Quill Travel 6.5" 5.9" (Opt. 7.9") 5.9" (Opt. 7.9")
Quill Diameter 3.3" 4.9" (Opt. 6.5") 4.9" (Opt. 6.5")
Main Motor 15 HP 20 HP (Opt. 30 HP) 20 HP (Opt. 30 HP)
Coolant Pump Motor 1/8 HP 1/8 HP 1/8 HP
Packing Dimension 137” / 186” / 219” x 41” x 52” 127" – 265" x 43" x 62" 127" – 265" x 43" x 66"
Gross Weight 7340 / 8994 / 11772 lbs 13800 – 27000 lbs 14450 – 29750 lbs

Accessories

Standard Accessories

  • 3-jaw chuck (15″)
  • Steady rest
  • Follow rest
  • Thread chasing dial
  • 4-position tool post
  • 4-position carriage stop
  • Coolant system with full-length splash guard

Optional Accessories

  • Digital Readout System
  • Aloris DA #5-SET (Tool post and 6 holders)
  • Royal spindle type live center
  • BTC 3-jaw chuck with back plate (Zero-set, 15″ D1-11)
  • Adaptor plate and rear 12″ 3 jaw chuck for back of spindle
  • Face plate (20″ D1-11)
  • Taper turning attachment
  • Micrometer carriage stop

Brochures

Title: Kent USA Heavy Duty Lathes Brochure

Videos

Kent USA Large Lathes Series

Request for Info