KTM-3VK

Features

  • 3  HP spindle motor, variable speed milling head with AC-Frequency drive, digital RPM display, analog load meter, and automatic spindle direction reversal when switching between high & low speed ranges
  • 9” x 49” hardened and ground table top
  • T-slots ground parallel to table ways
  • Table, saddle, and knee with hardened and ground dovetail ways
  • Precision ground leadscrews with backlash compensating double nut
  • Precision bored and ground milling head, with super precision ABEC-7 bearings
  • Meehanite® casting, with built in coolant reservoir in machine base
  • Automatic lubrication, with metered check-valves

   

Specifications

Specification KTM-3VSFKTM-3VKKTM-3VKF
Table Size 9" x 49" (9" x 42" Optional) 10" x 50" (10" x 54" Optional) 10" x 50" (10" x 54" Optional)
Table Travel (X-Axis) 35" 35" 35"
Saddle Travel (Y-Axis) 12" 15.25" 15.25"
Knee Travel (Z-Axis) 15" 15" 15"
Quill Travel 5" 5" 5"
Ram Travel 14.5" 22" 22"
Spindle Motor 3 HP 3 HP 3 HP
Spindle Speed 50–550–4500 RPM (2-range, Hi/Lo) 60–500–4200 RPM 50–550–4500 RPM (2-range, Hi/Lo)
Spindle Taper R-8 R-8 R-8
Quill Diameter 3.375" 3.375" 3.375"
Quill Feed Rate 0.0015" / 0.003" / 0.006" in/rev 0.0015" / 0.003" / 0.006" in/rev 0.0015" / 0.003" / 0.006" in/rev
Drilling Capacity (Manual / Power) 0.75" / 0.37" diameter 0.75" / 0.37" diameter 0.75" / 0.37" diameter
Boring Capacity 6" diameter 6" diameter 6" diameter
Milling Capacity 2.0 in³/min 2.0 in³/min 2.0 in³/min
Maximum Work Load (Center) 750 lbs 850 lbs 850 lbs
Spindle Center to Column 5" - 27" 2.75" - 17.75" 5" - 27"
Net Weight 2550 lbs 3000 lbs 3100 lbs
Gross Weight 2650 lbs 3100 lbs 3200 lbs
Shipping Dimensions 72" x 72" (skid) 76" x 76" x 88" (skid) 76" x 76" x 88" (skid)
Power Requirements 220v, 3 phase, 60 Hz, 10 Amp (optional 440v power requires 5A) but can also accept 220v, 1-phase power (15A) without a phase converter, ideal for customers with only 1-phase power 220 volts, 3 phase, 60 Hz, 10 Amp (optional 440v, requires 5 Amp) 220 volts, 3 phase, 60 Hz, 10 Amp (optional 440v, requires 5 Amp)

Accessories

Optional Accessories

  • Digital Readout System (View Brochure)
  • Table (X-Axis) Power Feed
  • Saddle (Y-Axis) Power Feed
  • Knee (Z-Axis) Power Feed
  • Air Power Drawbar
  • Flood Coolant System
  • Chip Pan
  • Riser Block
  • Angle-Lock Vise
  • Rustlick Coolant
  • Right angle milling attachment with arbor support
  • # 30 taper spindle option
  • Rotary table (12”, vertical and horizontal)
  • Clamping kit (52 pc)
  • R-8 collet set (11 pc/set, 1/8” to 3/4″)
  • Upgrade to 440V power

Brochures

Title: Kent USA Mill Brochure 2018

Request for Info